Tools/Maintenance

- PTFE additives reduce friction and energy consumption - Waxed based formula reduces metal to metal contact - Excels in dry, dusty conditions - Protects against rust development and corrosion - Prevents chain wear - Does not attract contaminants - Ideal for MTB, Road and Cyclocross - Can be applied to chain, cleats, shifters and derailleurs

The BKM-1.2 Hydraulic Brake Bleed Kit will bleed most models of mineral oil-based hydraulic bicycle disc brakes, including models made by Shimano®, Magura®, TRP®, Tektro®, Trick Stuff®, SRAM® DB8, Campagnolo®, Promax®, and Clarks®. Bleeding of hydraulic brakes removes air bubbles and contaminants from the braking system, for long-lasting components and peak performance. The BKM-1.2 is built for the rigors of daily commercial use and includes two syringes, hoses with shutoff clips, multi-size bleed blocks, a bleed funnel, and a set of our unique mountable syringe holders, as well as multiple hose fittings to fit the multiple standards found on hydraulic bicycle brake systems. Every part is replaceable and available from Park Tool. Housed in a rugged storage case. Includes: -  Two 20 mL syringes -  Two hose assemblies with shutoff clips -  One hose assembly with integrated fitting for bleed nipples such as those found on Shimano® mineral oil brake systems -  One open-ended hose assembly -  Bleed funnel with stopper -  Two 10 mm/12 mm universal bleed blocks -  Two 11 mm bleed blocks -  Two adjustable syringe holders -  M4 x 0.7 adapters — SRAM® DB8, Trick Stuff®, Campagnolo® (x2) -  M5 x 0.8 adapter — Formula™ Cura™, Tektro®, Hayes® (x2) -  M6 x 0.75 adapter — Magura® -  M6 x 1.0 adapters — universal (x2) -  M6 x 1.0 adapter — Promax® -  M7 x 0.75 adapter — Shimano® -  Hose compression sleeve — universal -  Fluid disposal bag -  Set of spare O-rings and hose -  Replacement parts available -  Brake fluid not included NOTE: The BKM-1.2 is for mineral oil-based hydraulic bicycle brake systems only. DOT fluid and mineral oil should never be mixed in the brake system or in their respective service tools. Cross-contamination of brake fluid may cause seal failure which may result in brake failure. For brakes using DOT fluid use the Park Tool BKD-1.2 Hydraulic Brake Bleed Kit — DOT.

Park Tool's CTP-4K includes four replacement chain tool pins and one 5/32" ball bearing. To replace the chain tool pin, unscrew the cap, and pull out the old pin. Use care not to lose the ball bearing beneath the pin. Install the new pin and replace the cap. Works with the CT-4.3, CT-4.2, CT-4, and CT-11

Park Tool's Utility Pick Set is a set of three unique, multi-purpose picks ideal for a wide variety of detail work. Features: • Aluminum handle with magnet • Picks are replaceable, cold formed, heat treated and polished high carbon steel • Set includes 1-straight, 1-hook and 1-90 degree pick

Handy and affordable, this tool makes it easy to get a clean cut every time. - Securely holds hose while cutting - Replaceable blade - Plastic body

Tools for repairing and maintaining SRAM Level brakes.

You know that $300 carbon bar you just bought? Don't guess when installing it. Know exactly. Topeak's D-Torq is a precision digital torque wrench made from hardened steel. It features an audible alarm when you start to over tighten. The reversing rachet mechanism in the head has convenient thumb articulation and a range of 1-20 Nm. The LCD readout makes it easy to know exactly where you are and can calculate Nm/kg, Nm/cm, inch/lbs and foot/lbs.

- The wrench is used to remove and install Shimano Hollowtech II, Campagnolo Ultra-Torque and Power Torque, Race Face, FSA, SRAM, Truvativ, Chris King bottom brackets - Small wrench is included for removal and installation of Shimano plastic bolts that are used on the Hollowtech II cranksets - Material: premium flex plus carbon steel, Surface finish: chrome plated according to ISO1456:2009

- 15 mm opening is laser cut with precision and perfect angle to help you loosen the pedals as easy as possible - 270mm of length for extra leverage - Small and light weight, perfect for toolbox and traveling

Features ball-end hex wrenches which are specially useful for working under angle

The wrench is used for tightening and unscrewing screws with 2, 2.5, and 3mm hex-shaped nuts.

Park Tool's Replacement Chain Tool Pin (2-Pack) fits Park Tool's CT-1, CT-2, CT-3, CT-3.2, CT-5, and CT-7 Chain Tools. • Made from hardened alloy tool steel • Uses 7mm or 9/32" 12 pt box end/socket • Sold singly or in pairs

This is a single replacement pin for Park Tool HCW-4 and SPA-6 pin spanner wrenches.

Precision brake bleeding tools and adaptor kits for Magura brake systems.

- Heat treated - Individual hex keys

Specially formulated low-friction lubricant for the seals and bushings of the air chamber for front and rear Fox Racing Shox. Float Fluid is the recommended lube for use with Fox forks and shocks. - Use when rebuilding Fox suspension to lubricate foam rings and seals - Corrosion inhibitor

Bleed fittings specifically designed for Hayes hydraulic disc brakes.

Inserts and removes Presta valve cores

- Adjusts rear wheel for centering in frame - Size: 3/8" - Color: Silver

For Shimano and Truvativ cranks. Use with a 6mm hex key.

- Tire Lever Set (3 pcs) - Zinc-plated steel

High-quality bits for recessed Torx Plus screws. Torx Plus profile: in comparison to normal Torx profiles, the enlargement of the 6 torque-transferring flanks between the tool and the screw is effected by means of an ellipse-shaped profile design and not a circular one. This means that the power applied when screwdriving is spread over a larger area. Higher torque is transferred and the service life of the screw and tool is also enhanced. - For Torx Plus screws - Particularly hard for semi-hard materials - 1/4" hexagon drive - High torque transfer - Size: 40 IP x 25mm

Refill pack for the Park Tool TPT-1 Tubeless Plug Tire Tool and other similar tools. These vulcanized rubber plugs are used to temporarily repair punctures in tubeless bicycle tire systems. Set of 5. NOTE: Intended for tubeless bicycle tires using sealant only. Not compatible with inner tube systems.

Prestalever is Quicker and Speedier than anything you've ever used. Our Patent-Pending Rim Hook with Honeycomb reinforced Box-Section Design is the key to our faster, safer, easy-to-use tool. Remove tires in seconds! Prestalever is Quicker and Speedier than anything you've ever used. Our Patent-Pending Rim Hook with Honeycomb reinforced box-section is the key to our faster, safer, easy-to-use tool. As you scoop the tire bead with the Prestalever, the slot underneath we call the "rim hook" naturally drops inside the rim. It prevents the Prestalever from slipping out, so you don't drop the bead. The rim hook stops the Prestalever at an easy-to-hold angle on the side of the rim. Then you simply glide the lever around the rim, and the tire peels-off as you go. The Prestlever is made of slippery Nylon, greatly reducing the force needed to remove tires. When you're done, twist the Prestalever 90 degrees to raise the rim hook out of the rim. Our box-section design allows the twist-action to easily stop at 90 degrees so the lever slides out easily. Install tires without strain. Our thick tip on the tire installer-end prevents catching and pinching tubes inside your tire. The bead-grabbing edge gives the right balance between leverage and lifting force, making it as easy as possible to complete tire installation. Presta Core tool is now essential. Even Bicycle Presta tubes now include removable cores. This gives you the added option of using tire sealant inside the tube of your standard tire. Removable cores are not always fully tightened at the factory. A loose core could cause slow leaks, or could even become unscrewed while using inflation devices. Tubes should be checked during installation and regularly afterwards for Presta core tightness. Don't carry an extra tool for chains! The Prestalever quick-link breaker is an effective emergency tool if you need to remove your chain on the road. The Patented design is the creation of Prestacycle's good friend and associate – cycling engineer Tomo Ichikawa. It removes the quick-link, which is the only function you need. When quick links are installed, pedal pressure can lock the installed quick link without any tools. For regular chain service, we still recommend a quick link tool, but with our feature, you no longer need to carry a separate tool with you on the bike. Quick-link removal Instructions: Place the quick Link near the top of the crank Jump the chain forward one tooth so the quick-link stands-up Use the slot on the Prestalever to push down FIRMLY. (The crank tooth will support the other end from underneath.) T-handle Tubeless Tire Plugger (optional parts required – Available 12/15/2021) The center of the Prestalever has threads which accept our Tubeless tire plugger. It then forms a T-Handle for effective, centered pushing of the included "Bacon Strips" used to seal large cuts in Tubeless tires. Third-hand Tool for Hand Installation Certain tires have delicate beads. Tire manufacturers recommend hand-installation only. The Prestalever can be used as a "third-hand" tool. When you hand-install the bead in one direction, the tire starts lifting-out at the other end. Insert the lever at one end to hold the bead, then use BOTH hands to install the tire from the other end. Tubeless Tire Removal (or any Difficult Tire) The Prestalever is the #1 tool for removing difficult tires. Using two or three can help with the toughest tire and wheel combo's. Insert a lever, but do NOT flip it yet. The rim hook will hold the lever in place, but unlike traditional levers that hook onto spokes, the bead will NOT be tensioned. You can still fit-in more Prestalevers. Insert the levers spaced about 6 inches apart, then flip them all … one-at-a-time. Even the toughest tires will come right off the rim in seconds. Prestalever is different… designed from the start with real-world experience on bicycles. Specifications: - One-end: purpose-designed Tire Remover - The-other-end: purpose-designed Tire Installer - Presta Valve Core tool - Quick-link Chain breaker. - Threads make it a T-Handle Tubeless Tire plugger (plugging kit additional). - Use multiple levers for tough, delicate tires like Road Tubeless and Gumwall. - Dimensions: 100mm x 13mm x 12mm - Weight: 13 grams Disclaimer: Check with the manufacturer of your wheels and tires to verify application and fit. Some manufacturers specify hand installation and removal only. Always follow Manufacturer guidelines for tires and wheels.

High-quality Wera L-keys with color-coded, convenient plastic sleeve. The tool is quickly accessible and the ergonomic and pleasant handle is easy on the hands even at low temperatures. The Hex-Plus profile offers a larger contact surface within the screw head. This reduces the notching effects to a minimum and almost completely eliminates the risk of destroying the screw recess. The ball-end on the long arm allows for reliable working even in difficult installation situations. The BlackLaser surface treatment provides outstanding surface protection, even against corrosion, and a long service life. The tools are quickly to hand thanks to the laser-engraved and thereby wear-resistant size markings on the L-keys. - L-keys for hexagonal socket screws - Hex-Plus allows socket head screws to live longer - Color coded, easy-to-grip plastic sleeve, even at low temperatures - Hexagonal ballpoint on the long arm - Wear-resistant size marking

Put these beauties in your tool kit for quickly fixing flats on the road. - Light weight, low profile lever - Durable composite construction - Easy to get under the tire bead - Set of three levers to assist with hard-to-remove tires - Included cap keeps the set together

- Microcell is ergonomically contoured for maximum comfort and surface area

For dust cap removal on Origin8 XLT integrated cranks

• 5/6mm hex wrenches

- Heat treated - Individual hex key