Package comes with two pieces of rim tape for use with the Zipp clinchers. Woven nylon material. Tape is extra thin with a thickness of 0.5 mm. Note: For Zipp 700c and 650c aluminum/carbon hybrid clichers, use the 16 mm rim tape. For Zipp 30 wheel set use 18mm but for the wider Firecrest and Firestrike carbon clinchers use the 20mm x 1/2mm rim tape.
Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese rear hubs with 135mm spacing - Type: Hollow Axle - Threads: 10mm x 1 - Diameter: 10mm - Length: 146mm - 1 axle per bag
Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Taiwanese hubs - Type: Solid Axle - Threads: 9.5mm x 26tpi - Diameter: 9.5mm - Length: 155mm - 1 axle per bag
$94.95 - $100.00
WTB's proprietary 4D spoke drilling prevents binding and lateral loading of the spokes, while the spoke bed itself has been updated to provide a more compatible interface between the spoke and rim. Integration of the all-new Solid Strip on our TCS 2.0 rims delivers the easiest to mount and most reliable tubeless system we’ve ever made. Available in widths ranging from i23 to i45, because all bikes should benefit from lightweight rims. Features: - TCS 2.0 creates a more robust, easily installed and dependable tubeless system. - A recessed channel along the center of TCS 2.0 rims allows installation of the all-new Solid Strip, which prevents tubeless tape from sagging at the spoke holes and results in a smooth, consistent interface between the tire and rim. - 4D angled spoke drilling eliminates binding and lateral loading, and disperses tension more evenly over a greater area
- EVO E-Tour 20 24" double wall rim - Silver - Inner Rim Width: 19.8 mm - Rim Height: 16.8 mm - Pin joint construction - No Eyelets - Schrader valve - 36 holes
- Converts Schrader rims to Presta - Rubber - Sold individually
- Supplies full wheel illumination for 700c/29in wheels and smaller - Approximately 40 hrs of battery life - Water resistant design - Includes 3 (AA) batteries - Sold individually (1 wheel) - Easy to install
Going tubeless allows you to run low tire pressure for better traction while drastically reducing the chances of a flat. Stan's All Mountain 29er Tubeless Kit converts standard tubed wheels to tubeless so you can reap the benefits. Everything you need to go tubeless is included. Plus, you won't miss dealing with flat tires and you'll save money on tubes!
Stan's Cross Country 29er Rim Strip converts standard tubed wheels to tubeless so you can reap the benefits. Going tubeless allows you to run low tire pressure for better traction while drastically reducing the chances of a flat. Stan's rim strips create a tight seal with the tire bead, reducing the instances of "burping". Plus, you won't miss dealing with flat tires and you'll save money on tubes!
Going tubeless allows you to run low tire pressure for better traction while drastically reducing the chances of a flat. Stan's Cyclocross Tubeless Kit converts standard tubed wheels to tubeless so you can reap the benefits. Everything you need to go tubeless is included. Plus, you won't miss dealing with flat tires and you'll save money on tubes!
$12.50 - $29.00
Replacement bearings for Stan's NoTubes Neo hubs. Includes 2 bearings. - 26mm OD x 15mm ID - 7mm thick
$20.00 - $23.00
Rear end cap conversion kits for NoTubes Neo and Neo Ultimate hubs - SealLock end caps feature a low friction U-cup seal that snaps into place
$11.25 - $25.00
Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3
$37.95 - $57.99
Sta Tru Front Wheel - Single Wall rim - Hub/Brake Compatibility: Rim Brake - Wheel Size: 24-inch - ISO Diameter: 507 / 24-inch BMX - Valve: Schrader - Tire Type: Clincher
Internal O-rings, a grease sleeve, and high-quality cup and cone bearings lend this 105-level hub high durability and smooth rolling. - Internal O-rings and grease sleeve - High quality, sealed Cup & Cone Bearing - High durability and smooth rolling for sustained performance
$29.00 - $35.00
Switching to tubeless or in need of valve replacements? Serfas Tire RX replacement valves will do the trick. Available sizes of 32mm, 44mm, or 60mm valves with removable cores, extra valve core, and Schrader to Presta adapter with core removal tool. Please note, Due to the multi-step chemical process and variables involved in anodizing, colors may vary slightly between batches produced.
Salsa springs for Flip-Off skewers
SRAM's 406 hub borrows technology from its more expensive brethren to bring you a solid hub at a great price. An aluminum hubshell with machined flange offers no-nonsense durability. Dependable cup and cone bearings roll smooth for the long haul and a strong, steel quick-release axle holds up under pressure.
Whether the goal is a finish line, epic adventure or simply getting back home again, SRAM'S 900 hubs are ready for the challenge. On the inside, the smooth and durable DOUBLE TIME drive mechanism ensures rapid engagement for quick and confident pedal responsiveness. SPEEDBALL bearings provide smooth, long-lasting rotation performance. Multiple spoke-count and cassette-capability options, as well as interchangeable end caps, make the 900 hubs a perfect choice for any disc-equipped road, gravel, cyclocross, cross country, trail, or enduro bike. - Versatile driver body can accept ROAD or MTB drivetrain, full spline or XD cassettes - Fully convertible with tool-free end caps - BOOST variants - 24, 28 or 32 spoke holes
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
$203.59 - $262.59
- Elite Series convertible MTB hubs - Available in multiple axle configurations - Shimano and XD cassette body options with 6 pawl/54 point/6.6-degree engagement - Straight pull and J-bend spoke options - 6 bolt disc brake rotor compatible - Sealed bearings - Material: AL6061 J-Bend/QR: - PCD-L: 58mm - PCD-R: 58mm - LTF-L: 32.95mm - LTF-R: 48.45mm - CTF-L: 34.7mm - CTF-R: 19.2mm J-Bend/142 x 12mm: - PCD-L: 58mm - PCD-R: 58mm - LTF-L: 36.45mm - LTF-R: 51.95mm - CTF-L: 34.7mm - CTF-R: 19.2mm Straight Pull/QR: - PCD-L: 51mm - PCD-R: 51mm - LTF-L: 36.2mm - LTF-R: 50.1mm - CTF-L: 31.45mm - CTF-R: 17.55mm Straight Pull/142 x 12mm: - PCD-L: 51mm - PCD-R: 51mm - LTF-L: 39.7mm - LTF-R: 53.6mm - CTF-L: 31.45mm - CTF-R: 17.55mm
When you can’t even see a part, you might forget about it, but it doesn’t mean its not important. Flat tires are probably the most common bicycle failures. Many times, flats are caused by the rims, specifically the lack of protection from the rims' sharp edges. Good rim strips didn’t exist for BMX rims. They work well and improve the function of any 20 inch rim. If you forget about them, that means they are doing their job.
$9.99 - $153.99
Looking for a super lightweight but badass tubeless sealant? Boom, you've just found it my friend! No Puncture Hassle performs under the most brutal race conditions. The cutting-edge microfiber molecules fill the bigger holes and tears, whilst the advanced latex forms a strong seal instantly. The formula also contains a unique UV detection system that highlights any punctures you haven’t seen during your ride. Developed with the world's top downhillers and pro peloton teams, to give you the finest tire sealant available. It's non-corrosive and easily washes off with water. Compatible with tubeless ready and full UST wheels/tires, No Puncture Hassle works from 15psi-120psi and temperatures from -20°C to +50°C. Our pouch is designed to fit your Presta valve perfectly and is ideal to add to your toolkit or ride pack for emergency top ups on the go! - For Downhill, Enduro and Road tires - Seals tears and holes up to 6mm - Contains UV puncture detection - Won't dry out or ball - Works from 15psi-120psi and temperatures from -20°C to +50°C - Biodegradable
A well-loved favorite for its overall ride quality, the Ksyrium road wheel has long been considered a smart way to upgrade your bike. Now that it's available in a disc-brake version with our UST Road Tubeless technology, it's even smarter. For a reasonable price, you get all performance and dependability that go with the Ksyrium name plus the added benefits of tubeless, including less rolling resistance, a smoother ride quality, and a reduced risk of punctures. There's no other road tubeless system that's easier to use. Our UST rims and tires make it simple to change, mount, and inflate tires. The wide rims (19mm internal) are optimized for 28mm tires (and still compatible with 25mm), perfect for tackling a variety of road terrain with efficiency and control. Our patented ISM (Inter Spoke Milling) technology reduces weight for fast climbing and instant acceleration. The system is engineered specifically for disc brakes, with plenty of lateral stiffness for precise handling and total axle and freewheel compatibility. If you're looking for an upgrade that can immediately boost your road bike's performance, look no further. Roll faster and smoother with a reduced risk of punctures - No tube means no friction, so less rolling resistance and higher speeds. - Ride with lower tire pressure for smoother ride and a reduced risk of punctures. - UST system offers a perfect union between tire and wheel, so installation, removal, and maintenance are easy. Lightweight rims for easier climbing and faster acceleration - ISM machined, welded rims. - 19mm internal rim width for low rolling resistance and extra comfort with 28mm tires. Lateral stiffness boosts agility and efficiency - Optimized bearing placement - Straight-pull bladed double butted spokes deliver optimal stiffness.
Protect your tubes without adding bulk with these Rim Strips from FSA. They're lightweight, and come in different lengths according to wheel size. Peace-of-mind comes standard.
$177.90 - $223.90
The 350 road hub delivers the amazing performance you've come to expect from DT Swiss at an incredible value. Fast and reliable, these hubs will roll for thousands of nearly frictionless miles. Plus, DT's legendary Ratchet System ensures precise engagement no matter how hard you stomp on the pedals.
- Straight gauge 2.0mm with cold forging technology - Chrome nickel stainless steel with rolled threads - 222g @ 32h/265mm - Box of 100 - Nipples sold separately
The rim for high-impact riding. The BA30 is a quality alloy rim designed to withstand a real beating. This is the rim for high-impact riding when the trails are rough and rugged. With an internal bracing structure, the BA30 has torsional stiffness for directional control in demanding circumstances. The BA30 features a thick bead wall adjacent to the tire to resist impact deformation, with a wider, rounded top-edge to reduce sidewall cuts. The nipple/spoke bed is oriented to the spoke direction to reduce weakness caused by bend in the spoke at the nipple hole. The BA30 is made with premium alloy, extruded with an internal brace profile and carefully formed for consistent shape. It is then fusion welded and ground for a strong precise finish. Our fusion welding system leaves a perfect seamless joint that becomes the strongest section of the rim ensuring that your rim won’t split if you impact at the seam. - Premium extruded alloy - Fusion welded seam-ground finish - Internal bracing profile - Impact resistant design - Tubeless Ready - 27.5: 570g - 29: 610g - 27.5" ERD: 566mm - 29" ERD: 604mm
• Aluminum hub body with hollow steel axle • Fixed/Free • Sealed bearings • 120mm or 130mm rear spacing • 32 hole • 282 grams
This 11-speed freehub is only compatible with model-year 2013 (V8) and 2014 (V9) Zipp wheelsets. Check that your hub has a black end cap before using this freehub. Use the spacer for compatibility with 10-speed Shimano and SRAM drivetrains after installation. The red freehub is designed for SRAM or Shimano drivetrains and includes a spacer for 10-speed compatibility. The blue freehub is designed for Campagnolo drivetrains. The Campagnolo version requires one 0.25mm axle washer, which is included. - 10 to 11-speed wheel conversion can only be completed by an authorized Zipp Service Center - Not intended to convert older 10-speed freehub wheels to 11-speed freehub wheels - Only intended to swap freehub compatibility (SRAM/Shimano - Campagnolo) with current 11-speed wheels - Includes cassette spacer - Material: Aluminum
Page 1 of 27 Next page